收藏本站
LTC3209-1/LTC3209-2
OPERATIO
CAMHL
The CAMHL pin quickly selects the camera high register
for flash applications without reaccessing the I 2 C port.
When low the CAM current range will be controlled by the
camera low 4-bit register. When CAMHL is asserted high
the current range will be set by the camera high 4-bit
register. The dropout delay is reduced from 150ms to 2ms
when CAMHL is asserted high so that the charge pump
can quickly change modes if required. When CAMHL
is asserted from high to low the charge pump mode is reset
to 1x.
Thermal Protection
The LTC3209-1/LTC3209-2 have built-in overtemperature
protection. At internal die temperatures of around 150 ° C
thermal shutdown will occur. This will disable all of the
current sources and charge pump until the die has cooled
by about 15 ° C. This thermal cycling will continue until the
fault has been corrected.
R REF Current Set Resistor
The current set resistor is connected between the R REF pin
and ground. This resistor sets the full-scale current for all
three displays (MAIN, CAM and AUX) according to the
following equations:
A 24.3k, 1% resistor provides full-scale currents of 28mA
for the MAIN; 400mA (total) current for CAM and 13.75mA
for AUX current sources.
This input is protected against shorts to ground or
low value resistors <10k. When a fault is detected the
reference current amplifier is current limited. In addition
the current source outputs and charge pump are disabled.
Mode Switching
The LTC3209-1/LTC3209-2 will automatically switch from
1x mode to 1.5x mode and subsequently to 2x mode
whenever a dropout condition is detected at an LED pin.
Dropout occurs when a current source voltage becomes
too low for the programmed current to be supplied. When
switching modes the mode change will not occur unless
dropout has existed for 150ms. This delay will allow the
LEDs to warm up and achieve the final LED forward voltage
value. The dropout delay can be reduced to 2ms by
programming the Drop2ms bit C2 in the REGC register or
when the CAMHL pin is switched high when controlling
the CAM LEDs.
The mode will automatically switch back to 1x whenever a
data bit is updated via the I 2 C port or when CAMHL
switches from high to low. If the part is forced into either
1.5x mode or 2x mode to operate as a fixed voltage power
supply over I 2 C, no mode switching will occur until an I 2 C
MAIN =
1 . 23 V
R REF
? 550
update is given.
CAM =
CAM =
AUX =
1 . 23 V
R REF
1.23 V
R REF
1.23 V
R REF
? 7900
? 3950
? 272
(LTC3200 9 -1 )
( LTC 3209 -2 )
320912fa
12
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LTC3210EPD-1#TRPBF IC LED DRVR WHITE BCKLT 16-UTQFN
LTC3210EUD#TRPBF IC LED DRIVR WHITE BCKLGT 16-QFN
LTC3212EDDB#TRPBF IC LED DRIVER RGB 12-DFN
LTC3214EDD#TRPBF IC LED DRIVR WHITE BCKLGT 10-DFN
LTC3215EDD#PBF IC LED DRIVR WHITE BCKLGT 10-DFN
LTC3217EUD#TRPBF IC LED DRVR FLASH TORCH 16QFN
LTC3218EDDB#TRPBF IC LED DRVR FLASH TORCH 10DFN
LTC3219EUD#PBF IC LED DRIVR QVGA DISPLAY 20-QFN
相关代理商/技术参数
LTC3210 制造商:LINER 制造商全称:Linear Technology 功能描述:MAIN/CAM LED Controller in 3mm × 3mm QFN
LTC3210-1 制造商:LINER 制造商全称:Linear Technology 功能描述:MAIN/CAM LED Controller with 64-Step Brightness Control in 3mm × 3mm QFN
LTC3210-2 制造商:LINER 制造商全称:Linear Technology 功能描述:MAIN/CAM LED Controllers with 32-Step Brightness Control in 3mm × 3mm QFN
LTC3210-3 制造商:LINER 制造商全称:Linear Technology 功能描述:MAIN/CAM LED Controllers with 32-Step Brightness Control in 3mm × 3mm QFN
LTC3210EPD-1#PBF 功能描述:IC LED DRVR WHITE BCKLT 16-UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT
LTC3210EPD-1#TRPBF 功能描述:IC LED DRVR WHITE BCKLT 16-UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT
LTC3210EPD-1-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:MAIN/CAM LED Controller with 64-Step Brightness Control in 3mm × 3mm QFN
LTC3210EPD-1-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:MAIN/CAM LED Controller with 64-Step Brightness Control in 3mm × 3mm QFN